1150 Gs engine bars wanted

If you’re looking to clear out the garage or fill it back up post up your FOR SALE or WANTED here. No commercial sales, just personal stuff.
big al
Posts: 2196
Joined: Sun Feb 13, 2011 8:02 am
Has thanked: 2 times
Been thanked: 48 times

1150 Gs engine bars wanted

Post by big al » Wed Jan 08, 2020 5:01 pm

As per title
Engine bars wanted please. don't mind if paint flaking or cracking .
getting them powder coated.
Thanks
Big Al

Adventure Bike Rider New Issue Out Now
quaycrest
Posts: 9
Joined: Sun Dec 20, 2015 10:14 pm
Has thanked: 2 times

Re: 1150 Gs engine bars wanted

Post by quaycrest » Thu Jan 09, 2020 1:22 pm

Hi BigAl,

I have some engine bars for a r21 year 2001 r1150gs I took off my bike as I wanted a full upper and lower set I think they are Fehling make.

Let me know if these are of interest to you?

They are solid and appear undamaged with all mounting brackets but have a bit of surface rust on them.
rps20190316_145050.jpg
rps20190316_145050.jpg (96.34 KiB) Viewed 723 times

big al
Posts: 2196
Joined: Sun Feb 13, 2011 8:02 am
Has thanked: 2 times
Been thanked: 48 times

Re: 1150 Gs engine bars wanted

Post by big al » Thu Jan 09, 2020 7:27 pm

Hi quaycrest.
How much would you be asking for them please.

quaycrest
Posts: 9
Joined: Sun Dec 20, 2015 10:14 pm
Has thanked: 2 times

Re: 1150 Gs engine bars wanted

Post by quaycrest » Fri Jan 10, 2020 4:00 pm

Hi BigAl,

How about £75 plus postage?

big al
Posts: 2196
Joined: Sun Feb 13, 2011 8:02 am
Has thanked: 2 times
Been thanked: 48 times

Re: 1150 Gs engine bars wanted

Post by big al » Fri Jan 10, 2020 7:24 pm

Hi quaycrest.
I've got a rugged roads plate right where the connecting bar fits on the bars.
Any chance of some close up photos of that area please, so I may figure the plate to bars out.
Thanks.
Al.

quaycrest
Posts: 9
Joined: Sun Dec 20, 2015 10:14 pm
Has thanked: 2 times

Re: 1150 Gs engine bars wanted

Post by quaycrest » Fri Jan 10, 2020 8:16 pm

Hi Al,

These are the only other images I have of the bars as they are now off the bike.
rps20190316_145237.jpg
rps20190316_145237.jpg (103.45 KiB) Viewed 648 times
rps20190316_145237.jpg
rps20190316_145237.jpg (103.45 KiB) Viewed 648 times
Attachments
rps20190316_144804.jpg
rps20190316_144804.jpg (118.53 KiB) Viewed 648 times

big al
Posts: 2196
Joined: Sun Feb 13, 2011 8:02 am
Has thanked: 2 times
Been thanked: 48 times

Re: 1150 Gs engine bars wanted

Post by big al » Mon Jan 13, 2020 5:16 pm

Hi Quaycrest,
Do they fit underside of the bash plate please.

quaycrest
Posts: 9
Joined: Sun Dec 20, 2015 10:14 pm
Has thanked: 2 times

Re: 1150 Gs engine bars wanted

Post by quaycrest » Mon Jan 13, 2020 7:02 pm

Hi Big Al,

The bars mount at three points one under the tank onto the front subframe, one just above the rear of each cylinder and the last one is the mount bracket just above the exhaust cross pipe. So no fixings to underside of bashplate.
717173jpg.jpg
717173jpg.jpg (38.54 KiB) Viewed 546 times

big al
Posts: 2196
Joined: Sun Feb 13, 2011 8:02 am
Has thanked: 2 times
Been thanked: 48 times

Re: 1150 Gs engine bars wanted

Post by big al » Thu Jan 16, 2020 7:55 pm

Hi quaycrest.
I have a crud catcher mounted on the front cover.
How close is the joining bracket to the front engine cover please.
Was wondering if the bars would fit behind the cover.
Thanks
Al

quaycrest
Posts: 9
Joined: Sun Dec 20, 2015 10:14 pm
Has thanked: 2 times

Re: 1150 Gs engine bars wanted

Post by quaycrest » Thu Jan 16, 2020 9:48 pm

Hi Al,

From memory and looking at the images I provided I am sure its pretty close to the engine with little space between the bracket and block. Would the crud catcher fit over the bracket or could longer stand-offs be made?

Post Reply

Return to “FOR SALE - WANTED”

Who is online

Users browsing this forum: No registered users and 34 guests