Anybody any experience of these?
Slightly pricey maybe, But allows you to fit your favorite grips with no problems.
https://www.coolride.de/home
Heated Grips
- HedgeHopper
- Posts: 493
- Joined: Thu Oct 05, 2017 9:27 am
- Location: Over By There
- Has thanked: 58 times
- Been thanked: 174 times
Re: Heated Grips
I like the idea of being able to use your choice of grip, but wonder about the wires...do you have to drill a hole in your bars?
edit: just read the manual, 8mm hole needed, not too sure about that
edit: just read the manual, 8mm hole needed, not too sure about that
-
- Posts: 4443
- Joined: Thu Mar 07, 2013 6:14 pm
- Has thanked: 2280 times
- Been thanked: 992 times
Re: Heated Grips
Not to be a knocker but I don't like the 8mm hole idea either although you do drill for perches but to keep the install neat the hole would be pretty close to the clamps or bends? Between the clamps would work mind same as the customs? Also would the slug not just heat up the bars, perches and end weights first as they are more conductive ? Hey heated mirrors, good plan.
The secret of a long life is knowing when its time to go.
-
- Posts: 4443
- Joined: Thu Mar 07, 2013 6:14 pm
- Has thanked: 2280 times
- Been thanked: 992 times
-
- Posts: 306
- Joined: Mon Aug 06, 2012 9:34 am
- Been thanked: 17 times
Re: Heated Grips
Hedgehopper: " just read the manual, 8mm hole needed, not too sure about that"
Garryboy: "I wonder if 2 x 4mm holes would do as 8mm gotta weaken the bars?"
From section 2B of the installation instructions: "Alternatively, drill a 3 – 5 mm hole on each side of the handlebar underneath the switch units in order to route the connection cables into these." Then they suggest feeding the heater wires down the sheath for the switch wiring.
However, I doubt whether the 8mm hole will be much of a problem. It is located between the handlebar mounting clamps, so it is a part of the bars which is well supported and least liable to be stressed. An 8mm hole in one the handle bar bends might be a problem, but I doubt whether a central hole will be.
Also, the 8mm hole allows a proper grommet to be used, whereas they suggest a piece of heat shrink tube in the 3-5mm holes. They also suggest carefully deburring the hole using e.g. a Dremel.
Garryboy: "I wonder if 2 x 4mm holes would do as 8mm gotta weaken the bars?"
From section 2B of the installation instructions: "Alternatively, drill a 3 – 5 mm hole on each side of the handlebar underneath the switch units in order to route the connection cables into these." Then they suggest feeding the heater wires down the sheath for the switch wiring.
However, I doubt whether the 8mm hole will be much of a problem. It is located between the handlebar mounting clamps, so it is a part of the bars which is well supported and least liable to be stressed. An 8mm hole in one the handle bar bends might be a problem, but I doubt whether a central hole will be.
Also, the 8mm hole allows a proper grommet to be used, whereas they suggest a piece of heat shrink tube in the 3-5mm holes. They also suggest carefully deburring the hole using e.g. a Dremel.
- HedgeHopper
- Posts: 493
- Joined: Thu Oct 05, 2017 9:27 am
- Location: Over By There
- Has thanked: 58 times
- Been thanked: 174 times
Re: Heated Grips
dAMN MEANT TO EDIT AND DELETED...ANYWAY THANKS SLEDGE i READ THE WHOLE MANUAL NOW AS i SHOULD HAVE IN THE FIRST PLACE
Re: Heated Grips
I have used something similar, but quite a bit cheaper. Not sure of the brand name but they were made in New Zealand and supplied by Bob Porecha a Classic BMW specialist in South London. I have fitted them to various bikes and had no issues with the holes weakening the bars. Probably less chance of them weakening the bars than the wires from the more traditional heated grips getting damaged in an accident. They work best with shorter bars and hand guards or fairings. Not so great on my California whose bars are about five feet long.
Cheers Jak
Cheers Jak
Re: Heated Grips
From a structural point of view I can't see the 8mm hole being a problem. The loads on the bar are greatest at the
ends and at the points where they are clamped. The part in between will hardly be seeing any loads or forces.
ends and at the points where they are clamped. The part in between will hardly be seeing any loads or forces.
- Asgard
- Posts: 826
- Joined: Thu Jun 07, 2018 7:45 pm
- Location: Variable
- Has thanked: 174 times
- Been thanked: 381 times
Re: Heated Grips
Point of order, Loads are actually less at the ends of the bar, the same applies to the tip of any cantilevered component that is subjected to a force at it's end at right angle or oblique, but this allowed for in the design which will have more strength built in at the fixing point.
In the case of Bars they are thicker/larger diameter in that area
Its a trick............get an Axe