R1200gsa clutch on an 2006

Got a spanner in the works? Post your motorcycle problems here.
tefflon
Posts: 1184
Joined: Tue Jun 21, 2011 7:02 pm
Been thanked: 24 times

R1200gsa clutch on an 2006

Post by tefflon » Sun Feb 17, 2019 4:01 pm

Hi all
Is there any one in the Manchester area that could help a good friend of mine out he needs a new clutch fitting.

He thinks he could probably do it himself but then again and he hasn’t the funds to pay BMW prices

So any help would be good

Ta
tefflon

Adventure Bike Rider New Issue Out Now
Hugh
Posts: 519
Joined: Sat Sep 10, 2016 1:54 pm
Has thanked: 204 times
Been thanked: 289 times

Re: R1200gsa clutch on an 2006

Post by Hugh » Sun Feb 17, 2019 5:12 pm

Greetings,

Not sure just where in Manchester you need but for south Manchester the following are all good folks to try (non are BMW dealers though);

MW Motorcycles - Hyde - 0161 351 9989
Road & Racing - Hyde - 0161 366 5167
Howard & Son - Stockport - 0161 480 3825
College Motorcycles - Stockport - 0161 480 0778
Motomax - Chadkirk - 0161 484 5503
Focus Motorcycles - Stockport - 0161 474 1785
High Peak Motorcycles - New Mills - 01663 742289

TTFN

Hugh.

User avatar
cozi70
Posts: 487
Joined: Sat May 31, 2014 8:46 am
Location: Belfast
Has thanked: 16 times
Been thanked: 37 times

Re: R1200gsa clutch on an 2006

Post by cozi70 » Sun Feb 17, 2019 5:41 pm

tefflon wrote:
Sun Feb 17, 2019 4:01 pm
He thinks he could probably do it himself but then again and he hasn’t the funds to pay BMW prices
I looked into fitting one myself on my 2006 gs, being a previous motor mechanic,and it looked pretty straight forward like a rwd car,but upon closer research and a visit to my local independent bike fixer who was in the middle of doing one, they call it breaking the bike in half, literally from the bottom rear of the tank down it all needs removed,and I was also warned about the complications about bleeding the servo assisted brake system.
They also advised changing about 5 or 6 oil seals inside the bell housing/engine while striped.

Coyotedavebmw
Posts: 14
Joined: Wed Sep 20, 2017 7:09 pm
Location: Wakefield
Has thanked: 5 times
Been thanked: 4 times

Re: R1200gsa clutch on an 2006

Post by Coyotedavebmw » Sun Feb 17, 2019 5:55 pm

Roy Gardner, if he is still spannering.


Cheers Dave

tefflon
Posts: 1184
Joined: Tue Jun 21, 2011 7:02 pm
Been thanked: 24 times

Re: R1200gsa clutch on an 2006

Post by tefflon » Sun Feb 17, 2019 7:31 pm

Thanks boys iv passed it too my m8 thank you all

tefflon
Posts: 1184
Joined: Tue Jun 21, 2011 7:02 pm
Been thanked: 24 times

Re: R1200gsa clutch on an 2006

Post by tefflon » Sun Feb 17, 2019 9:25 pm

Nice to see MW motorcycles in Hugh’s list must say Chris & Alan are go good lads I use them to do my tyres and mot s

Ta Steve

User avatar
Teflon Jnr
Posts: 878
Joined: Sun Sep 13, 2015 2:12 pm
Location: Stalybridge
Has thanked: 4 times
Been thanked: 64 times

Re: R1200gsa clutch on an 2006

Post by Teflon Jnr » Sun Feb 17, 2019 9:41 pm

Agreed pops top chaps
Jesus rides a Harley and the devil wears prada

🇩🇪 🇧🇪 🇬🇧 🇮🇪 🇫🇷 🇮🇲 🇱🇺

Jack the Builder
Posts: 15
Joined: Fri Nov 03, 2017 9:39 pm
Location: Leigh
Been thanked: 3 times

Re: R1200gsa clutch on an 2006

Post by Jack the Builder » Sun Feb 17, 2019 10:11 pm

Coyotedavebmw wrote:
Sun Feb 17, 2019 5:55 pm
Roy Gardner, if he is still spannering.


Cheers Dave
He sure is, and a top bloke too. going to see him this week so he can work a little of the mechanical magic on the old beemer. :D

tefflon
Posts: 1184
Joined: Tue Jun 21, 2011 7:02 pm
Been thanked: 24 times

Re: R1200gsa clutch on an 2006

Post by tefflon » Sun Feb 17, 2019 11:08 pm

Hi
Would you have his number please

Ta Steve

Jack the Builder
Posts: 15
Joined: Fri Nov 03, 2017 9:39 pm
Location: Leigh
Been thanked: 3 times

Re: R1200gsa clutch on an 2006

Post by Jack the Builder » Mon Feb 18, 2019 9:33 am

tefflon wrote:
Sun Feb 17, 2019 11:08 pm
Hi
Would you have his number please

Ta Steve
Hello

If its roy you're after...

www.rgm-uk.com

01772 603781

Post Reply

Return to “TECHNICAL”

Who is online

Users browsing this forum: No registered users and 41 guests