Moroc bound

Redmurty · Post by **Redmurty** » Sat Jun 10, 2017 7:54 am

Mike54 wrote:And I've known some who could use some of this :laugh:

Cheers Mike just spat my tea all over my desk :laugh: :laugh: :laugh:

still chuckling :laugh: (thumbs)

cheers Spud

Simon_100 · Post by **Simon_100** » Sat Jun 10, 2017 10:31 am

Redmurty wrote:
known a few women that could of done with a re-bore :whistle:

cheers Spud

As long as you've got the tool to do the job ... :whistle:

Simon (thumbs)

SteveR · Post by **SteveR** » Sat Jun 10, 2017 12:02 pm

Redmurty wrote:She lives, she breathes, and her heart beats sweetly (thumbs)

now to ...... run her in 200 miles ish then to get down and dirty :laugh: :laugh: :laugh:

known a few women that could of done with a re-bore :whistle:

cheers Spud

Ouch. Well, we can always have a gentle ride out next week, bit of green lane and road work?

Redmurty · Post by **Redmurty** » Sat Jun 10, 2017 6:24 pm

The Spanish Biker wrote:
Redmurty wrote:
known a few women that could of done with a re-bore :whistle:

cheers Spud
As long as you've got the tool to do the job ... :whistle:

Simon (thumbs)

perhaps it wasn't the women after all then

cheers Spud

Redmurty · Post by **Redmurty** » Fri Jun 16, 2017 7:16 am

Pick the tiddler up today grand total for the bill £500 :whistle:
bike very quietly now and with very little mechanical sound (thumbs)
guess I will have to run it in this weekend then :woohoo:
cheers Spud

boboneleg · Post by **boboneleg** » Fri Jun 16, 2017 7:28 am

Considering the amount of work you had done I think that's a fair price (thumbs)

Redmurty · Post by **Redmurty** » Fri Jun 16, 2017 7:39 am

boboneleg wrote:Considering the amount of work you had done I think that's a fair price (thumbs)

more than fair I have a very large shit eating grin on my face at the moment (thumbs) the amount of work he has put in I expected a fair amount more B)

I know he's done valves and some head work (thumbs) and has said it should run better than before

cheers Spud

PHILinFRANCE · Post by **PHILinFRANCE** » Fri Jun 16, 2017 11:29 am

Nice one Spud , they do take a lot of killing (thumbs)

Redmurty · Post by **Redmurty** » Fri Jun 16, 2017 5:18 pm

video of her ticking over wont load ?

just been out for a little run down the lanes and she is so sweet (thumbs)

cheers Spud

boboneleg · Post by **boboneleg** » Fri Jun 16, 2017 9:47 pm

Hi Spud, I'm not trying to tell you how to suck eggs or anything but here's something that gets neglected on a lot of DR350's.

At the bottom of the frame downtube is an oil screen, they can be a bit of a bitch to get out but with plenty of heat (I use a hot air gun) and a good 19mm deep recessed socket they will come out.

If it is not taken out and cleaned every so often it can get blocked and that usually results the top end being cooked. I am doing some surgery on my bike at the moment so I took a photo of mine today.

: DR350OilScreen008.JPG (88.45 KiB) Viewed 1192 times

Moroc bound

Re: Moroc bound

Re: Moroc bound

Re: Moroc bound

Re: Moroc bound

Re: Moroc bound

Re: Moroc bound

Re: Moroc bound

Re: Moroc bound

Re: Moroc bound

Re: Moroc bound