Search found 41 matches
- Fri Oct 28, 2016 2:19 pm
- Forum: TRAVEL
- Topic: Motorcycle Accident
- Replies: 3
- Views: 782
Re: Motorcycle Accident
Bad news there Sarge, hope people will be ok.
- Fri Oct 28, 2016 1:49 pm
- Forum: GREEN LANES, TRAILS and OFF-ROAD
- Topic: SARN HELEN again
- Replies: 64
- Views: 24822
Re: SARN HELEN again
I read a few years ago about the case being dropped against the members of the TRF when a group of riders on the Sarn were caught, but the others were prosecuted. I then asked the question of the status of the sarn about 2 years ago on the old VDSR forum, and one of the replies stated that a person ...
- Tue Aug 02, 2016 4:11 pm
- Forum: ACCESSORIES
- Topic: Heated grips review in printed mag anyone?
- Replies: 9
- Views: 3220
Re: Heated grips review in printed mag anyone?
Hi, i bought the same as sarge. One set for tenere, other for ttr. I am happy with them £22 per set plus postage i think off the bay
- Wed May 18, 2016 10:31 am
- Forum: THE PUB
- Topic: Does this remind you of someone?
- Replies: 2
- Views: 1515
Re: Does this remind you of someone?
I must have been sleeping.zzzzzzzzzzzzzzzzzzzzzzzzzzzzzzzzzzzz
- Wed May 18, 2016 10:16 am
- Forum: THE PUB
- Topic: Does this remind you of someone?
- Replies: 2
- Views: 1515
- Tue Apr 12, 2016 4:04 pm
- Forum: TECHNICAL
- Topic: The Bavarian Cheese Factory
- Replies: 9
- Views: 2860
Re: The Bavarian Cheese Factory
I would not fancy using an impact driver. 24mm head, what diameter is the actual bolt, is there a chance to drill it and tap a smaller thread in (12-13 mm)??
- Tue Apr 12, 2016 3:31 pm
- Forum: TECHNICAL
- Topic: Short Levers for KLX250
- Replies: 4
- Views: 1865
Re: Short Levers for KLX250
Can you do what i did to my ttr 250? Cut the ball end off. File it round. There was a hole in the ball end already, but if not drill one yourself, approx 8-10 mm. Cut approx 1" off the lever or more if you wish. Grind the end round then slide ball on. If you are happy with the length, epoxy the...
- Fri Apr 08, 2016 9:01 pm
- Forum: TECHNICAL
- Topic: 1/2" Breaker Bar Recommendations?
- Replies: 14
- Views: 3832
Re: 1/2" Breaker Bar Recommendations?
I've got a draper expert, done me alright over the years.
- Mon Feb 29, 2016 9:37 pm
- Forum: TECHNICAL
- Topic: xt660z clutch advise please
- Replies: 16
- Views: 5102
Re: xt660z clutch advise please
Stratarider, you didn't read my post I guess. Don't tell me what I know, it's not my first bike. Have you checked the alignment of the "release mechanism arm"? With the arm pushed forward, the punch mark on the arm should align with the one on the cover. You can either remove the cover an...
- Sun Feb 28, 2016 2:08 pm
- Forum: TECHNICAL
- Topic: xt660z clutch advise please
- Replies: 16
- Views: 5102
Re: xt660z clutch advise please
Hi, an extract out of my 2012 tenere hand book. Adjusting the clutch lever free play The clutch lever free play should measure 10.0-15.0 mm (0.39-0.59 in) as shown. Periodically check the clutch lever free play and, if necessary, adjust it as follows. 1. Slide the rubber cover back at the clutch lev...